LEESON Electric Corporation

ELECTRIC MOTORS, GEARMOTORS AND DRIVES

DC Integral Gearmotors
 
 
PZ Series DC Gearmotors

General Specifications:
These gearmotors are designed for continuous duty service over a 60:1 speed range. All have constant torque operation throughout this speed range when powered by a full-wave unfiltered SCR-type adjustable speed control having a typical form factor of 1.3 to 4. Low voltage gearmotors are designed for battery power or can be used with a low voltage controller with form factor up to 1.05.
 
Mechanical Specifications:
  • Output shafts utilize needle bearings for high load capacities
  • Shafts are hardened Steel
  • Lubrication by semi-fluid grease
  • First stage gear is helical type followed by-spur type gears
Mechanical Specifications:
These gearmotors are designed for mounting at any angle, but shaft up with motor below should be avoided to prevent leakage of lubricant into the motor should the motor’s shaft seal fail. Gear-head damage may occur if gearmotor is stalled, especially in the ratios of 60:1 or higher. Overhung load capacities shown are at center of output shaft. Model PZ gearmotors have the same mounting dimensions as Bodine model D and Z gearmotors, Bison 100 gearmotors, and Baldor/Boehm PSS, plus many of the Dayton brand gearmotors.
 
Available Ratings: PZ Series -TENV – 90 & 180 Volt - 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
4 40 1/40 450 155 90
4 40 1/40 450 155 180
10 100 1/20 180 155 90
10 100 1/20 180 155 180
20 100 1/20 90 155 90
20 100 1/20 90 155 180
30 100 1/17 60 155 90
30 100 1/17 60 155 180
60 56 1/17 30 171 90
60 56 1/17 30 171 180
100 36 1/17 18 171 90
100 36 1/17 18 171 180
150 24 1/17 12 180 90
150 24 1/17 12 180 180
300 10 1/17 6 180 90
300 10 1/17 6 180 180
 
Available Ratings: PZ Series -TENV – Low-Voltage - 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
10 100 1/20 180 155 12
30 100 1/17 60 155 12
55 56 1/17 30 171 12
 
P300 Series DC Gearmotors
General Specifications:
These gearmotors are designed for continuous duty service over a 60:1 speed range. All have constant torque operation throughout this speed range when powered by a full-wave unfiltered SCR-type adjustable speed control having a typical form factor of 1.3 to 4. Low voltage gearmotors are designed for battery power or can be used with a low voltage controller with form factor up to 1.05.
 
Mechanical Specifications:
  • Output shafts utilize needle bearings for high load capacities
  • Shafts are hardened Steel
  • Lubrication by semi-fluid grease
  • First stage gear is helical type followed by-spur type gears
Application Notes:
These gearmotors are designed for mounting at any angle, but shaft up with motor below should be avoided to prevent leakage of lubricant into the motor should the motor’s shaft seal fail. Gear-head damage may occur if gearmotor is stalled, especially in the ratios of 60:1 or higher. Overhung load capacities shown are at center of output shaft. Model 300 gearmotors have the same mounting dimensions as Bison’s 300 gearmotors, and many of the Dayton brand gearmotors.
 
Available Ratings: P300 Series -TENV – SCR Rated - 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
5 353 1/20 336 565 90
9 268 1/20 216 474 90
18 150 1/20 103 385 90
20 140 1/20 90 370 180
24 280 1/8 76 353 90
31 220 1/8 58 327 90
31 220 1/8 58 327 180
34 82 1/20 52 318 90
51 130 1/8 35 277 90
51 130 1/8 35 277 180
51 55 1/20 35 281 90
61 113 1/8 29 267 90
60 45 1/20 29 267 180
94 77 1/8 19 236 90
94 77 1/8 19 236 180
109 27 1/20 16 224 90
106 26 1/20 16 222 180
167 43 1/8 11 197 90
170 43 1/8 11 196 180
 
Available Ratings: P300 Series -TENV – Low-Voltage - 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
5 353 1/20 336 565 12
31 220 1/8 58 327 12
51 130 1/8 35 277 12
61 113 1/8 29 267 12
 
PE350 Series DC Gearmotors

General Specifications:
These gearmotors are designed for continuous duty service over a 60:1 speed range. All have constant torque operation throughout this speed range when powered by a full-wave unfiltered SCR-type adjustable speed control having a typical form factor of 1.3 to 4. Low voltage gearmotors are designed for battery power or can be used with a low voltage controller with form factor up to 1.05.
 
Mechanical Specifications:
  • Oversized output bearings for greater overhung load capacity
  • Shafts are of high-carbon Steel
  • Gears are splash lubricated with permanent heavy duty gear oil
  • Rugged aluminum die cast housings used
  • Precision machined gearing is hardened
Application Notes:
Sub-fractional AC Gearmotors that are totally enclosed for continuous duty, general-purpose applications. These gearmotors are designed for mounting at any angle, but shaft-up with motor below gearhead is not recommended. Gears and bearings are splash lubricated with permanent, heavy-duty gear oil. All gearing is designed and rated to AGMA Class 9 standards to withstand momentary shock overload of 200%. Model PE350 gearmotors have the same mounting dimensions as Bodine’s “E” box and Baldor gearmotors.
 
Available Ratings: PE350 - SCR Rated – TENV – 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
7 330 1/8 336 565 90
7 330 1/8 336 565 180
14 341 1/8 180 465 90
14 341 1/8 180 465 180
21 371 1/4 124 413 90
21 371 1/4 124 413 180
27 305 1/4 91 374 90
27 305 1/4 91 374 180
42 280 1/4 58 327 90
42 280 1/4 58 327 180
50 250 1/4 50 315 90
50 250 1/4 50 315 180
62 220 1/4 43 303 90
62 220 1/4 43 303 180
83 155 1/4 29 267 90
83 155 1/4 29 267 180
125 100 1/4 23 256 90
125 100 1/4 23 256 180
165 70 1/4 15 232 90
165 70 1/4 15 232 180
250 45 1/4 10 201 90
250 45 1/4 10 201 180
500 25 1/4 5 194 90
500 25 1/4 5 194 180
 
Available Ratings: PE350 Series -TENV – Low-Voltage - 1.0 S.F
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
14 341 1/8 180 465 12
42 325 1/4 58 327 12
62 220 1/4 43 303 12
83 155 1/4 29 267 12
 
P1100 Series DC Gearmotors
General Specifications:
Our line of P1100, DC Gearmotors utilize Fractional horsepower, permanent magnet, DC motors. They are totally enclosed designs for continuous duty, general purpose applications, rated for 90 Volts DC input, having a form factor of 1.3 to 1.4. Low voltage P1100 gearmotors are rated for 12 Volts DC input, with form factor up to 1.05.
 
Mechanical Specifications:
  • Oversized output bearings for greater overhung load capacity
  • Shafts are of high-carbon Steel
  • Gears are splash lubricated with permanent heavy duty gear oil
  • Rugged aluminum die cast housings used
  • Precision machined gearing is hardened
 
Application Notes:
Sub-fractional AC Gearmotors that are totally enclosed for continuous duty, general-purpose applications. These gearmotors are designed for mounting at any angle, but shaft-up with motor below gearhead is not recommended. Gears and bearings are splash lubricated with permanent, heavy-duty gear oil. All gearing is designed and rated to AGMA Class 9 standards to withstand momentary shock overload of 200%. Model P1100 gearmotors have the same mounting dimensions as Bison 483 gearmotors and many Dayton brand gearmotors.
 
Available Ratings: P1100 - SCR Rated – TENV – 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
8 1087 1/4 212 700 90
12 1030 1/4 143 700 90
18 750 1/4 95 700 90
42 353 1/4 42 650 90
60 238 1/4 29 625 90
92 160 1/4 19 575 90
135 105 1/4 13 525 90
18 1112 1/2 95 700 90
33 822 1/2 53 650 90
42 705 1/2 42 650 90
60 476 1/2 29 625 90
92 320 1/2 19 575 90
135 210 1/2 13 525 90
 
Available Ratings: P1100 Series -TENV – Low-Voltage - 1.0 S.F
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
8 1087 1/4 212 700 12
60 238 1/4 29 625 12
42 705 1/2 42 650 12
92 320 1/2 19 575 12
 
OS300 Series DC Gearmotors

General Specifications:
Our line of OS300 Series, DC Gearmotors utilize Fractional horsepower, permanent magnet, DC motors. They are totally enclosed designs for continuous duty, general purpose applications, rated for 90 Volts DC input, having a form factor of 1.3 to 1.4. Low voltage OS300 gearmotors are rated for 12 Volts DC input, with form factor up to 1.05.
 
Mechanical Specifications:
  • Output shafts utilize needle bearings for high load capacities
  • Shafts are hardened Steel
  • Lubrication by semi-fluid grease
  • First stage gear is helical type followed by-spur type gears
 
Application Notes:
Sub-fractional AC Gearmotors that are totally enclosed for continuous duty, general-purpose applications. These gearmotors are designed for mounting at any angle, but shaft-up with motor below gearhead is not recommended. Overhung load capacities are shown at center of output shaft. A current limiting device such as an SCR control should be used to prevent damage.
 
Available Ratings: OS300 - SCR Rated – TENV – 1.0 S.F. – Off-Set Shaft
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
9 268 1/20 210 474 90
19 150 1/20 103 385 90
24 280 1/8 76 353 90
31 220 1/8 58 327 90
51 130 1/8 58 277 90
 
Available Ratings: OS300 – Low Voltage – TENV – 1.0 S.F. – Off-Set Shaft
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
9 268 1/20 210 474 12
19 150 1/20 103 385 12
24 280 1/8 76 353 12
31 220 1/8 58 327 12
51 130 1/8 58 277 12
 
 
Right-Angle Series DC Gearmotors
General Specifications:
Our line of Right-Angle, DC Gearmotors utilize Fractional horsepower, permanent magnet, DC motors. They are totally enclosed designs for continuous duty, general purpose applications, rated for 90 & 180 Volts DC input, having a form factor of 1.3 to 1.4. Low voltage OS300 gearmotors are rated for 12 Volts DC input, with form factor up to 1.05.
 
Mechanical Specifications:
  • Lubrication by permanent oil bath
  • Output shaft is interchangeable for left hand or right hand style
  • Shafts are hardened Steel
  • Worm-type right-angle gearing features hardened steel and bronze worm gears for long life and quiet operation
 
Mechanical Specifications:
For optimum seal life, these right angle gearmotors have a lubrication breather positioned for horizontal mounting. For other mountings, the breather plug must be reoriented by u sing a 90-1/8 NPT taper pipe elbow. However, shaft up with motor below should be avoided to prevent leakage of lubricant into the motor should the motor’s shaft seal fail.
 
Available Ratings: Right-Angle - SCR Rated – TENV – 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
42 22 1/17 60 185 90
62 19 1/17 40 185 90
125 16 1/17 20 185 90
250 10 1/17 10 185 90
500 5 1/17 5 185 90
42 30 1/12 60 235 180
62 35 1/12 40 235 180
125 18 1/12 20 235 180
250 10 1/12 10 235 180
500 5 1/12 5 235 180
42 80 1/8 60 235 90
62 70 1/8 40 235 90
62 70 1/8 40 235 180
125 45 1/8 20 235 90
125 45 1/8 20 235 180
250 25 1/8 10 235 90
250 25 1/8 10 235 180
500 13 1/8 5 235 90
500 13 1/8 5 235 180
62 135 1/4 40 235 90
62 135 1/4 40 235 180
83 125 1/4 30 235 90
83 125 1/4 30 235 180
125 90 1/4 20 235 90
125 90 1/4 20 235 180
250 50 1/4 10 235 90
250 50 1/4 10 235 180
500 30 1/4 5 235 90
500 30 1/4 5 235 180
 
Available Ratings: Right-Angle – Low-Voltage – TENV – 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Over-hung Load (Lb.) Voltage
42 80 1/8 60 235 12
250 25 1/8 10 235 12
62 135 1/4 40 235 12
125 90 1/4 20 235 12
 
Series 12 - Right-Angle Series DC Gearmotors
General Specifications:
Our line of Series 12, Right-Angle, DC Gearmotors utilize Fractional horsepower, permanent magnet, DC motors. They are totally enclosed designs for continuous duty, general-purpose applications, rated for 90 Volts DC input, having a form factor of 1.3 to 1.4. Low voltage, Series 12, Right-Angle gearmotors are rated for 12 Volts DC input, with form factor up to 1.05.
Mechanical Specifications:
  • Vacuum impregnated single-piece cast aluminum housings
  • High temperature Nitrile seals used
  • Shafts are hardened Steel
  • Worm-type right-angle gearing features hardened steel and bronze worm gears for long life and quiet operation
  • Solid output shaft can be easily converted to hollow type
 
Available Ratings: Series 12 - SCR Rated – TEFC – 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Voltage
28 125 1/8 61 90
45 87 1/8 39 90
58 158 1/4 30 90
90 100 1/4 19 90
115 85 1/4 15 90
167 61 1/4 10.6 90
250 46 1/4 7 90
 
Available Ratings: Series 12 – Low-Voltage – TENV – 1.0 S.F.
Output RPM F.L. Torque (In.Lbs.) Input HP Ratio to 1 Voltage
27 134 1/8 61 12
45 94 1/8 39 12
58 158 1/4 30 12
90 100 1/4 19 12
115 85 1/4 15 12
167 61 1/4 10.6 12
250 46 1/4 7 12
 
logo
Catalog Pages -
DC Integral Gearmotors