LEESON Electric Corporation  

DC – Washguard Duty - White Epoxy and All Stainless DC Motors

 
LEESON Washguard Duty DC motors are designed for extended life in applications requiring regular washdown or otherwise wet environments.  These White Epoxy painted and All Stainless DC motors retard the entrance of water during cleaning operations and their drain holes release and water that does enter the motor.  The interior of the motor is also coated, which offers extra protection to the motor’s interior surfaces to prevent corrosion. 
 
 
White Epoxy DC Motor
White Epoxy DC Motor Features:
  • High Quality 303 Stainless Steel Shafts
  • Spring loaded contact seals and patented “V” ring Forsheda seal
  • Interior surfaces are protected by an enamel and polyester coating
  • External surfaces painted with USDA approved Epoxy paint
  • Stainless steel fan guards and conduit box cover
  • Double sealed, over-sized bearings are used
 
Available Ratings – SCR and Low Voltage:

C-Face With Removable Base – 90 & 180 V – 1750 RPM – ¼ - 1.5 HP
SUB-FHP – 90 V – TENV – Square Flange or C-Face – 1/8, 1/6 (1750 RPM), & ¼ HP (2500 RPM)
SUB-FHP – 90 V – TENV – Square Flange or C-Face – 1/8, 1/6 (1750 RPM), & ¼ HP (2500 RPM)
IEC Frame – 180 Volts – TENV IP55 – B-5 Flange with Removable B3 Base – ½HP (.37 kW) &  3/4HP (.55 kW)

 
 

dscf0027dscf0029dscf0033

IP55 - SUB-FHP Washguard Gearmotors Feautures:

DC Permanent Magnet gearmotors rated for continuous duty.  Designed for use with fullwave non-filtered SCR controls or battery supplied low voltage for adjustable speed applications requiring constant torque throughout the speed range.

 
IP55 - SUB-FHP Washguard Gearmotors Mechanical Features:
  • Shafts coated with Mirolon 3300 fortified Teflon for corrosion resistance
  • Frames, endshields, armature and interior components protected to resist corrosion
  • Cast Conduit Box with threaded conduit holes
  • Stainless Steel hardware throughout
  • Output shafts have needle bearings for high load capacities
Ratings:
P300 Series – 90 Volt – Parallel Shaft - TENV
Output RPM F.L. Torque Input HP Ratio to 1 Over-hung Load (Lb.)
5 353 1/20 336 565
31 220 1/8 58 327
51 130 1/8 35 277
94 77 1/8 19 236
167 43 1/8 11 197
 
P300 Series – 12 Volt – Parallel Shaft – TENV
Output RPM F.L. Torque Input HP Ratio to 1 Over-hung Load (Lb.)
5 353 1/20 336 565
31 220 1/8 58 327
51 130 1/8 35 277
 
PE350 Series – 90 Volt - Parallel Shaft – TENV
Output RPM F.L. Torque Input HP Ratio to 1 Over-hung Load (Lb.)
14 341 1/8 180 465
42 280 1/4 58 327
83 155 1/4 29 267
250 45 1/4 10 201
500 25 1/4 5 194
 
PE350 Series – 12 Volt - Parallel Shaft – TENV
Output RPM F.L. Torque Input HP Ratio to 1 Over-hung Load (Lb.)
14 341 1/8 180 465
42 280 1/4 58 327
 
Right Angle – 90 Volt – TENV
Output RPM F.L. Torque Input HP Ratio to 1 Over-hung Load (Lb.)
42 80 1/8 60 235
250 25 1/8 10 235
62 135 1/4 40 235
125 90 1/4 20 235
250 50 1/4 10 235
 
Right Angle – 12 Volt – TENV
Output RPM F.L. Torque Input HP Ratio to 1 Over-hung Load (Lb.)
62 135 1/4 40 235
125 90 1/4 20 235
 
 
Extreme Duck LogoAll Stainless DC Motors
All Stainless DC Motor Features:
  • All exterior components are 300-series stainless steel
  • Full fact nameplates are laser etched in motor frame
  • Endshields are O-ring sealed to motor frame
  • Double lipped Viton® shaft seals
  • Constant torque throughout speed range
  • Oversized brushes for long brush life

C-Face With base and C-Face Less Base

  • 1/4 HP to 1 HP
  • 90 Volt and 180 Volt

 

logo
Catalog Pages -
DC – Washguard Duty